Why this stripe needs a plan before you cut
Stripes Navy from Sunshine Blvd by Amber Kemp-Gerstel for Riley Blake Designs is a 100% cotton print with thin, rainbow-colored stripes on a navy ground. The stripes are directional, so the way you place your pattern pieces or rotary-cut strips decides whether they run across a quilt block, down a garment, or along a binding edge.
Before you cut, decide which way you want the stripes to travel in the finished project. That single choice drives your layout, your cutting order, and how much fabric you need. The print is 43"/44" wide, so plan piece sizes around that usable width.
Fabric facts that shape your cutting plan
- Stripes Navy from Sunshine Blvd by Amber Kemp-Gerstel for Riley Blake: 100% cotton, 43"/44" wide, item C12103-NAVY from the Sunshine Blvd collection by Amber Kemp-Gerstel for Riley Blake Designs. The cotton hand and the 43"/44" width set your maximum strip length and help you estimate yardage for directional cuts.

Stripes Navy from Sunshine Blvd by Amber Kemp-Gerstel for Riley Blake - Stripes Navy from Sunshine Blvd by Amber Kemp-Gerstel for Riley Blake: The print features thin, rainbow-colored stripes on navy. Thin stripes read as a fine line at a distance, so a small shift in alignment shows up quickly in seams and bindings.
- Stripes Navy from Sunshine Blvd by Amber Kemp-Gerstel for Riley Blake: Care: machine wash cold, tumble dry low. Pre-washing before cutting lets the cotton shrink and settle so your stripe alignment stays true after the first wash.
Find the stripe direction and square the cut
- Pre-wash and press: Machine wash cold and tumble dry low as the care instructions state, then press the cotton smooth. Wrinkles distort the stripe line and make it harder to judge whether your cut is square.
- Identify the stripe run: Lay the fabric flat and look at which way the thin rainbow stripes travel. Mark that direction with a pin or a small chalk arrow on the wrong side so every later cut follows the same orientation.
- Straighten one edge: Make a fresh cut along a stripe or a thread line rather than trusting the mill edge. A straight starting edge is what keeps every following strip parallel to the stripes.
- Cut strips or pieces in one direction: Once your reference edge is straight, cut all strips or pattern pieces from the same orientation. Flipping pieces between cuts is the most common way stripe direction gets reversed in a finished project.
- Label as you go: Stack cut pieces with a small note or pin marking the top edge. When you return to sew, the label tells you which way the stripes should run without re-checking each piece.
Sewing stripes without a wavy seam
Thin stripes reward a slow, deliberate seam. Pin or clip at each stripe intersection before sewing, and sew with the stripe line as your guide rather than the fabric edge alone. If a seam starts to drift, stop, re-align the stripes, and continue.
Press seams as you go instead of waiting until the end. Pressing each seam flat before opening it keeps the stripe line crisp and prevents the navy ground from puckering around the rainbow lines. A dry iron on a cotton setting is enough; the care label covers washing and drying, not iron temperature, so test on a scrap first.
Directional stripe projects that suit this print
Because the stripes are directional, choose projects where a consistent stripe run is part of the design rather than an accident.
- Stripe-matched quilt binding: Cut binding strips parallel to the stripes so the rainbow lines run along the binding edge. This gives a clean, deliberate finish and uses the print's direction as a feature.
- Rail-fence or strip-pieced blocks: Alternate stripe direction block by block to create a woven look, or keep every strip parallel for a calm, linear effect. Decide the rule before you cut so all blocks match.
- Simple apparel details: The cotton is suitable for apparel per the collection description. Use the stripes on a yoke, pocket, or cuff where a consistent direction is easy to control.
- Home decor accents: Pillow backs, table runners, and small home decor pieces let the thin rainbow stripes carry the design without complex pattern matching.
When to cut with the stripe and when to cut across it
- Cut with the stripe: Choose this when you want long, continuous lines, as in binding, sashing, or a vertical garment detail. It uses the 43"/44" width for length and keeps the rainbow lines unbroken.
- Cut across the stripe: Choose this when you want the stripes to run horizontally across a block or a hem. Crosswise cuts change the direction of the rainbow lines and need a fresh straight reference edge each time.
Buying enough for directional cuts
Directional prints can use more yardage than a random print because you cannot always rotate a piece to fit. Sketch your cutting layout before you order, and add a little extra for matching stripes at seams. The catalog price is USD 3.48, with a comparison price of USD 5.80, so buying the right amount up front is easier than sourcing a matching dye lot later.
If your project depends on a specific stripe repeat or a wider usable width than 43"/44", check the fabric listing before you commit. The supplied information does not include a stripe repeat measurement, so measure the print yourself on a swatch if exact matching matters to your design.

